Menu
DISH's cutting-edge DVR technology delivers just what you need no matter what type of TV setup you have. Our DVR receivers range from our Hopper Duo, designed to support one or two TVs, to our cutting-edge Hopper 3, which supports up to seven TVs and lets you record up to 16 shows at once —. Then do a satellite auto tune, NOT a Freesat tune. My TV found 1600 TV channels! Find the RTL Television channel and add to favourites, then find all the other channels you want, e.g. BBC 1 HD, 2 HD, ITV HD, and Channel 4 HD (yes CH 4 HD is there!) and add these to your favourites. How to Align a Satellite Dish. Tune your receiver - If you don't have a signal meter, you will have to use your receiver's on-screen meter. Firstly, make sure you are tuned to an active channel or transponder and that all the parameters are correct - Frequency 10.774GHz, Symbol Rate 22000, Polarisation Horizontal, (FEC Auto or 5/6) is. Jun 19, 2019 Scanning (or rescanning) for channels is mostly an automated process. All you have to do set that process in motion through a few simple steps. And while these steps are different for each TV, the process is pretty similar on every TV out there. Make sure your TV is connected to an antenna. Press the “Menu” button on your remote control.
Diseqc motors offer a cheap and convenient method for tracking the Clarke Belt with your satellite dish. They can be easily aligned if you take a few initial precautions and follow the steps outlined below.
Installing the Motor
1. Check the pole - ensure that the mounting pole is perfectly straight with a level or inclinometer. If the pole is not level, your dish will not properly track the arc of satellites.
2. Attach the Diseqc motor to the pole - tighten the motor fittings.
3. Set the elevation angle on the motor - the elevation angle on the motor will be based on the latitude of your location. The manual for the motor will tell you what to set this angle to or alternatively, you can use the following table:
Latitude | Elevation | Declination |
50 | 39 | 6.6 |
51 | 38 | 6.7 |
52 | 37 | 6.8 All with a user-interface that is a model of clarity, speed and ease-of-use. Antares auto-tune live vst au rtas software download. Hailed at its introduction as a 'holy grail of recording,' by Recording magazine (and adopted worldwide as the largest-selling audio plug-in of all time), Auto-Tune corrects intonation and timing problems in vocals or solo instruments, without distortion or artifacts, while preserving all of the expressive nuance of the original performance - with audio quality so pristine that the only difference between what goes in and what comes out is the intonation and timing. |
53 | 36 | 6.9 |
54 | 35 | 7.0 |
55 | 7.1 |
For example, Athlone, which has a latitude of 53 degrees, will require an elevation angle of 36 degrees. The angle can be set according to the markings on the side of the motor. Some motors even include the latitude markings as an additional aid.
4. Attach the dish to the motor shaft - make sure the dish is at right angles to the motor and pole.
5. Set the adjusted declination angle on the dish - your latitude will also determine the declination angle - see above. Most diseqc motors use a special adjusted declination angle formula (based on the tilt of the rotating motor shaft) which will again be specified in your manual. For example, Athlone, with latitude of 53 degrees, will require a declination angle of approximately 7 degrees. A Moteck SG-2100, a common diseqc motor, uses the formula 30 – declination angle. So for Athlone the adjusted declination angle is 23 degrees (i.e. 30-7) when using an SG-2100. This angle can be set according to the markings on the side of the dish.
Setting the adjusted declination angle
Note: If you have a different model of motor, it will use a different formula for the adjusted declination angle.
This method relies on aligning the motor with true south using a satellite which is positioned at or near true south for your location. In this case, we will use Atlantic Bird 2 located at 8 West as our reference for true south.
1. Slightly loosen the motor fittings - this will enable you to just rotate the motor about the pole. Don't loosen the fittings too much or it will complicate matters.
2. Connect up a satellite meter or alternatively tune the receiver - make sure to tune to an active transponder - the Orbit transponder (11178, H, 27500) is a good choice.
3. Rotate the dish and motor until you see activity on the signal meter - rotate slowly both the dish and motor on the pole until the signal meter is at a maximum. A compass or the position of the sun may be useful in locating true south.
Rotating the dish and motor
4. Tighten the fittings - once the satellite has been found and the signal is at a maximum, tighten the motor fittings to the pole to ensure everything is firmly locked in position.
Note: For people located on the east coast of Ireland, Atlantic Bird 3 at 5 West may provide better tracking. In that case, use the same procedure as above, but with the France 2 transponder (11591, V, 20000) as your reference.
USALS (aka GotoX or Diseqc 1.3) allows you to quickly and accurately align your dish. As most receivers are now USALS compatible, this method provides much better tracking of the Clarke Belt than the 'True South' approach. This is due to the fact that it is more precise to align your dish at the eastern or western extremes of the arc than at the top of the arc (i.e. near true south).
1. Enter you latitude and longitude into the receiver - enter your location coordinates into the the USALS menu of your receiver.
2. Drive the motor to a satellite towards the east or west - select a satellite in the USALS menu and drive or GOTO that satellite. A good choice is Turksat at 42E as it has a strong signal over Ireland.
3. Rotate the dish and motor until you see activity on the signal meter - loosen the pole fittings slightly and rotate slowly both the dish and motor on the pole until the signal meter is at a maximum. If you don't have a signal meter, then watch the quality meter on the satellite receiver which has been tuned to an active transponder. For Turksat, the TRT 1 transponder (11920, V, 24440) is suitable.
4. Tighten the fittings - once the satellite has been found and the signal is at a maximum, tighten the motor fittings to the pole to ensure everything is firmly locked in position.
Once you believe the motor has been properly aligned, it's a good idea to confirm with a few tests. We will use 5 satellites which are spread across the Clarke Belt.
Extreme East Turksat 42E - TRT 1 : 11920, V, 24440
East Hotbird 13E - Al Jazeera : 11034, V, 27500
South Atlantic Bird 2 8W - Orbit : 11178, H, 27500
West Hispasat 30W - Retevision : 12547, V, 30000
Extreme West Intelsat 9 58W - Aastha Channel 2 : 11477, H, 26462
East Hotbird 13E - Al Jazeera : 11034, V, 27500
South Atlantic Bird 2 8W - Orbit : 11178, H, 27500
West Hispasat 30W - Retevision : 12547, V, 30000
Extreme West Intelsat 9 58W - Aastha Channel 2 : 11477, H, 26462
If you run into problems, firstly recheck the pole is level - this is critical for proper tracking. Double check your elevation and declination angles and ensure the motor axis is properly aligned with true south. The following diagram will help you to locate any faults.
Offset dishes may appear to be pointed low towards the horizon, when in fact they are aiming at a much high elevation as shown in the above diagram.
Getting Started
If you've never aligned a dish before, it can be very frustrating, especially if you don't have a signal meter of some sort. You may well end up thinking the receiver is faulty. Digital channels are either 'on' or 'off' and do not fade in or out gradually like analogue signals, further adding to the difficulty. Waving a dish about in the deluded hope that you will somehow find the correct location without either setting the elevation angle or knowing the azimuth angle is a complete and utter waste of time. However, if you follow the steps outlined below you will succeed .. eventually!
1. Attach the F-connectors - Make sure that the cable and F-connectors are properly fitted. The inner core of the coax cable and the outer braid must never come in contact with each other.
2. Set the elevation angle - For the majority of novice satellite users, the satellite they wish to align to is the Astra2/Eurobird cluster at 28 degrees east. This is where Sky, BBC, ITV and C4 are transmitted from. For Ireland, the dish elevation for Astra2 is approximately 22 degrees.
Most offset dishes have an elevation scale on the mounting bracket which allows you to adjust the dish to the correct elevation.
How To Set Autotune On Dish Network
For satellites other than Astra2, a list of approximate elevation angles is provided.
How To Set Auto Tune On Dish Tv
3. Tune your receiver - If you don't have a signal meter, you will have to use your receiver's on-screen meter. Firstly, make sure you are tuned to an active channel or transponder and that all the parameters are correct - Frequency 10.774GHz, Symbol Rate 22000, Polarisation Horizontal, (FEC Auto or 5/6) is suitable for the BBC channels on Astra2.
You may have to enter the Setup/Installation menu in order to have a constant display of the meter.